• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window Pane Window Panes

A damaged or cracked window can be a nuisance. It could also be an opportunity to upgrade your glass to energy-efficient or insulated windows, and reap benefits like greater comfort, a higher the value of resales and lower utility bills.

It's a task you can take on yourself for only a fraction of the cost of hiring a professional. You'll only require the appropriate tools and a few hours of your time.

Glass

Replace your old single-paned windows with tempered insulate glass to improve energy efficiency, cut down on noise, and maintain the historical integrity of your older home. A majority of homeowners with hand tools can replace windows with ease. You will also require a replacement windows near me window pane, glazier's tips pliers, and latex glaze putty. If needed, you can use a heating gun to warm the old putty. Before starting, wear gloves and safety goggles as working with broken glass may cause injuries.

Remove any broken glass pieces that remain. It is best to use pliers however, a flathead may be useful equally. Then, use a wood chisel, or putty knife, to remove the rest of the old putty from around the frame and the sash. Be careful to not scratch the window sash. Be careful and slow. This should be done on an elevated ladder, not on the ground. Also, have someone on the ground to ensure it is held steady.

After you have removed all the old putty, it is time to prepare the window frame to fit the new pane. Take measurements of the width and height of the opening in the sash, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Take these measurements to the nearest hardware store or home center, and get a piece of stock glass cut to size. You can also cut the glass yourself, if you have the appropriate tools.

After putting the new pane in place After installing the new pane, apply a small amount of caulking along the edge to ensure it is weatherproof. Install a glazier’s point on both sides of the frame. This will help secure the pane. The points should not be so tight that they cause friction between the frame and sash, but they should also not be loose.

Before applying the putty, work it in a gentle manner until it's soft and free of lumps. Make it into pencil-sized strips. Apply the first strip in the corner of the frame, moving from one corner to another so that it is even and smooth.

Glazier's Points

The glazier's points are the small triangular pieces of metal which help to secure glass into a window frame without scratching or damaging the delicate surface. Learning how to use these hidden tiny helpers is simple and can save you money on a professional installation or the cost of buying new glass.

After removing the old putty, glazier points as well as any remaining remnants clean the frame thoroughly using a utility knife. Lightly sand the wood in the rabbet grooves, if necessary, to smooth out rough areas. If you do sand the wood, make sure to protect it with painter's tape to avoid accidental damage.

Write down the dimensions of the frame. Bring these measurements to a hardware store or Replace window pane a home center and have the new pane cut slightly smaller than the frame's opening. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Place the new pane into the frame and push it in place by using your hands. Then, use the tip of your chisel or back of the putty knife to make a tap on the glazier's points as illustrated in Figure 11. The glazier's points should be aligned with the top edge of the pane and the shoulders raised should be just below that lip.

Apply a thin layer of glazing compound to the rabbet grooves as well as the edges of the new glass. This will protect and seal the edges. Allow it to dry and cure completely.

Install the new window sash when the glazing compound has dried. First, coat the wood with a heavy coat of Linseed oil. This will stop the new putty from drying out or cracking when it absorbs moisture. Apply the coat using a brush or the tip of your putty knife, and then use the chisel, or the back end of the putty knife to gently hammer in the new sash and glazier's point into the grooves of the rabbet. Repeat this process every 10 inches around the frame's perimeter.

Putty

A baseball that is thrown, an errant rock or a falling branch can cause a window to crack or break. Fortunately, the majority of windows can be easily replaced by simply putting a brand new piece of glass in its place. The glass is held into the position with a tiny metal clip, referred to as a glazier’s point and putty. This compound is also known as glazing compound. Remove the old pane and clean the area using an abrasive, pull-type scraper, or a wood chisel. Wear gloves and safety glasses while doing this work. You'll require a heat gun if the window is glued to the frame.

If you're planning to install the original sash, remove any pieces of molding that secure the old pane. Then you can sand the sash down to make sure it's flat and ready for a new caulk. After the sash has been re-installed and sanded, apply a fresh silicone caulk around the glass to ensure that it doesn't swell or fade as time passes.

Remove the glazing points from the rabbets, the grooves in the sash, where the glass sits. If they're difficult to chisel, use an instrument like a heat gun over them for a few minutes to soften them. If you're using a heating gun, make sure not to scratch the railings of the sash or the sash itself by placing the tool too close.

After the old glaze points and putty are removed, make a bed for the new pane. Roll a rope of glazing compound between your hands, and form it into a 1/2-inch thick. Place it into the rabbets, where the glass will be put. The glass must rest against the putty on both sides. If you need to gently tap your glass into the rabbet using your thumb.

If the new pane is cracked then you can seal it with a solvent-based glue or silicone caulk prior to pressing it into the sash. In other cases, you'll need to putty over the crack to create an airtight seal and keep water out. When the putty dries then clean the oily film off the glass using the help of a rag. Allow it to completely dry before painting. If you paint before the putty has completely dry, it will not form an effective seal and could discolor or leak in time.

Paint

If you've had a broken window pane, you might be concerned about the expense of replacing it. It's true that replacing a single piece of glass doesn't need to be expensive even if you do it your own. In fact windows with double glazed replacement windows panes can be replaced for less than the cost of an expert.

First, if you're working on a large window, make sure that it is securely attached to the frame. This task can be done relatively easy and fast using the appropriate tools and techniques.

When you're ready to start, begin by removing the old window by prying out the glazing points of metal that are connected to it. These are basically small metal triangles that act as "nails" which hold the window in place within the frame of wood. They are submerged beneath a glaze putty or bead which hardens into solid wedge that holds the wood frame firmly in position and hides the points.

After removal of the old pane clean the frame and the wood. Scrape off any paint that has been used and sand the rabbet grooves where the glazing points were placed. These should be sanded down to bare wood to allow you to paint them the same color as the rest the frame. After sanding the wood then apply a layer of flax oil. This will help extend its life.

Then, take measurements of the dimensions of the window's opening. It is necessary to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. To determine the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasonal change. Take these measurements to your local hardware or home improvement store and ask them to cut you a piece cut for you.

Now, Replace window pane it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.